Were you interested in suggestions about Tools You Need to Install a New Bathtub ?
Setting up a tub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bathtub with a new one is also a moderately challenging job. If the old bathtub is conveniently obtainable, the project can move immediately; if you need to open a wall surface to get rid of the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub as well as embeded in the new one. Ensure you have actually certified on your own for the job and also are comfortable trying it. Rather than employing a service provider to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Chances are you may require a professional plumber to make tube connections.
This write-up will assist you set up a brand-new bathtub in your shower room if you have actually already acquired a new bathtub and do not require to alter the setup of your previous supply of water pipelines.
Your tools as well as product checklist must comprise the following:
Getting ready for the Installment
Firstly, the sustaining structure supplied with the bath must be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make sure that if the faucet comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets device to avoid stress on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you use all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be rather bothersome due to the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have been eliminated, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. Once the taps have been removed, the holes in the bath/basin will need to be cleansed of any old sealing compound.
Before carrying on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are useful in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four little points.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the tub up until the spirit level checks out level.
To install taps, fit the bottom of the furthest flexible faucet adapter to the ideal supply pipeline by making a compression join; then do the same for the other tap.
Activate the water and also examine all joints and also brand-new pipework for leaks as well as tighten them if required. Fill the bathtub as well as additionally examine the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the maker's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has actually been made use of a minimum of once as this will resolve it right into its final position.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making sure that the washers are in location between the faucet and the sink. Secure the faucet in place with the maker provided backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be attached to the tap ends initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to fracture an inflexible seal, creating the water to penetrate the wall surface between the bath as well as the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures and installations. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to permit the movement experienced when the tub remains in usage. The sealant can break relatively very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the market. It is advisable to fit the ceramic tiles utilizing waterproof or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that piece of writing about How to Install a Bathtub while doing a search on the search engines. Those who appreciated our blog post please be sure to share it. I treasure reading our article about How to Install a Bathtub.
Get An Estimate